Impulse PCW-5181 User Manual Page 80
- Page / 120
- Table of contents
- BOOKMARKS
- User’s Manual 1
- Version: 1.0 3
- Table of Contents 5
- Chapter 1 - Impulse Overview 7
- Chapter 1 - Overview 8
- Chapter 2 - Shipping Contents 10
- Typical Impulse Applications 11
- CAUTION! 12
- Connecting an IDC Motor 13
- Connecting a Non-IDC Motor 13
- SS-RS232 14
- Daisy-Chaining Impulse Drives 15
- Multi-Dropping with RS-485 15
- Jumpers 9 pin D 25 pin D 16
- RTS to CTS 7 to 8 4 to 5 16
- DSR to DTR 4 to 6 6 to 20 16
- C. Connecting an IDC Keypad 17
- D. Connecting AC Power 18
- E. LED Diagnostic Indications 18
- Application Notes 19
- G. Mounting the Impulse Drive 20
- Impulse Dimensions 21
- Installation 22
- Impulse DIN-Rail Mounting 23
- Using Application Developer 26
- Upload Project 27
- Launch Now 28
- Open an Existing Project 28
- Using the Project Wizard 29
- Fine-Tuning Your Application 34
- See Appendix C 35
- Mechanics 36
- Command Signal Configuration 37
- Jog Input Configuration 37
- Numeric Precision 38
- X-Smoothness #1 39
- X-Smoothness #2 40
- X-Smoothness #3 40
- Advanced (Advanced Tuning) 41
- I/O Setup 42
- Output Descriptions 44
- File Menu 47
- Edit Menu 47
- Setup Menu 47
- Communications Menu 48
- Run Menu 49
- View Menu 50
- Loading the Operating System 51
- Keypad Features 53
- Keypad Hardware Features 54
- Keypad Menu Structure 56
- Apply Power to the Keypad 57
- Using the RUN Menus 58
- Using the EDIT Menus 59
- File Menu (FILE OPTIONS) 59
- Renaming an Open Project File 60
- > FILE > RENAME 60
- Using the HELP Menu 61
- Using the COPY Menu 62
- Using the DEL (Delete) menu 62
- JOG PARAMETERS 66
- ACCEL LOW_V HIGH _V 66
- I/O SETUP 72
- Configuring Inputs 72
- > SETUP > I/O 72
- Configuring Outputs 73
- Stored-Move Profiles 74
- > MOVE 74
- Configuring Scan Time 75
- > UNIT# 76
- Impulse Specifications 77
- RX TX +5V 78
- Keypad Mounting *Template 79
- Impulse I/O Schematics 80
- Application Notes: 81
- Impulse I/O Accessories 83
- 25-pin Connector 84
- Impulse-Applicable IDC Motors 85
- IDC Motor Wiring 86
- Parallel 89
- Limits Tables 93
- Chapter 8 - Product Support 95
- Warranty & Repairs 96
- Possible Ground Loop 97
- Communications Protoco 99
- Byte Receive Time Out 100
- Receive Buffer Overrun 100
- Read Queries 100
- Write Requests 101
- User Accessible Parameters 102
- Jog Acceleration Rate 103
- 75 SerMvSel 106
- Commanded Velocity (RAM Only) 107
- EEPROM Enable Switch 109
- System Status (RAM Only) 110
- Unit Address 111
- Software Shutdown (RAM Only) 112
- Custom or User-Defined Motors 114
- Anti -Resonance 116
- Do Not Print This Page 119
- Inserted as Placeholder 119
- 3925 Cypress Drive 120
- Petaluma, CA USA 94954 120
© 2020, manymanuals.com. All rights reserved. | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals